|
Sonifex
Redbox Range
|
|
Sonifex
"Redbox" - In Depth Information
|
|
|
The
new Sonifex "Redbox" Range consists of various inexpensive interconnection
boxes for use in various applications for radio stations, TV
studios, video and recording studios. These units are housed
in red anodized aluminium boxes which can be screw mounted or
rack mounted. All connections and controls are on the rear panel.
|
|
|
Matching
Converters |
|
|
RB-UL1
The RB-UL1 is an Unbalanced to Balanced Single
Converter for interfacing domestic, or semi-pro unbalanced equipment
to professional balanced line levels.
|
|
|
RB-UL2
The RB-UL2 is a Dual Unbalanced to Balanced Converter
for interfacing domestic, or semi-pro unbalanced equipment to
professional balanced line levels.
|
|
|
RB-UL4
The RB-UL4 is a Quad Unbalanced to Balanced Converter stereo unit
for interfacing domestic, or semi-pro unbalanced equipment to
professional balanced line levels.
|
|
|
RB-BL2
The
RB-BL2 is a bi-directional stereo unit for interfacing domestic,
or semi-pro unbalanced equipment to professional balanced line
levels and vice-versa.
|
|
|
RB-BL4
The RB-BL4 is a dual bi-directional stereo unit
for interfacing domestic, or semi-pro unbalanced equipment to
professional balanced line levels and vice-versa.
|
|
|
RB-LI2
The RB-LI2 stereo line isolation
unit is used to isolate audio signals from inter area ground hum
loops, which could be caused by equipment being powered by different
mains power supplies, or different phases on the same supply.
|
|
|
RB-PLI6
The RB-PLI6 Passive Line Isolation
Unit is used to isolate audio signals from inter-area ground hum
loops, which could be caused by equipment being powered by different
mains power supplies or phases on the same supply. The input and
output are connected together through a transformer, and the unit
has internal jumpers allowing the inputs and/or outputs to be
balanced about ground. The unit requires no mains power for operation.
This unit is useful where audio is required to be driven over
a relatively long length of cable. By isolating the signal using
transformers, ground loop currents which can be present in non-isolated
signals, are eradicated completely.
|
|
|
RB-PA2
The RB-PA2 is a dual stereo RIAA
equalised phono amplifier. This record player preamp amplifies
the small signal from your pick up cartridge (either moving magnet
or high output moving coil magnetic) and provides the necessary
RIAA equalisation required for vinyl records, to match it to a
line input of your mixer, or amplifier. It uses a clean RIAA response
making it ideal for use with broadcast turntables and DJ decks
and where vinyl records are being archived to CD for high quality
transfers, or for converting albums to mp3.
|
|
|
|
|
|
Mixers
& Source Selectors
|
|
|
RB-SS10
The RB-SS10 10 Way Stereo Analogue Source Selector/Mixer
is a 1U rack-mount unit that produces a stereo analogue audio
output from 10 selectable stereo analogue sources. There are 10
illuminated front panel push buttons, which select and indicate
the current channel selection. The selection and indication is
also available through a remote connector on the rear panel. To
stop accidental front panel selection there is a remote input
to inhibit the front panel buttons.
|
|
|
RB-DSS10
The RB-DSS10 Digital Source Selector is a 1U rack-mount
which produces an AES/EBU and S/PDIF level digital audio output
from 10 selectable AES/EBU or S/PDIF digital input signals. There
are 10 illuminated front panel push buttons, which select and
indicate the current channel selection. The selection and indication
is also available through a remote connector on the rear panel.
To stop accidental front panel selection there is a remote input
to inhibit the front panel buttons.
|
|
|
RB-PMX4
The RB-PMX4 is a high performance 10 mono input
to 4 mono output preset mixer. Each of the four outputs has a
10 way DIP switch associated with it to select which of the 10
inputs are routed to it. So, by altering the DIP switches, any
of the input sources can be mixed to any of the outputs. The DIP
switches are enclosed by a screw-on cover on the front panel so
that the settings can not be accidently changed for secure applications.
|
|
|
|
|
|
Headphone
Distribution Amplifiers
|
|
|
RB-HD1
The RB-HD1 is a 1U rack-mount stereo headphone
amplifier for driving up to two pairs of professional stereo headphones
from a single stereo or mono input. One headphone socket is on
the front panel with one on the rear.
|
|
|
RB-HD6
The RB-HD6 headphone distribution amplifier is
a 1U rack-mount which distributes stereo audio to up to 6 different
sets of headphones, or can be used as 6 independent headphone
amplifiers, each with their own input and volume control. A typical
application might be to provide common headphone feeds for guests
in a radio studio, with a separately derived feed, perhaps including
talk-back, for the presenter.
|
|
|
RB-DHD6
The RB-DHD6 digital 6 way headphone distribution
amplifier is a 1U rack-mount which receives a digital input signal,
as either AES/EBU or S/PDIF and converts it to 6 individually
buffered, jack-plug, headphone outputs, each with their own volume
control.
Useful for connection to digital mixing desks, digital routers
and matrices, the RB-DHD6 connects directly to an AES/EBU or S/PDIF
output to provide the highest quality audio directly to the headphones.
|
|
|
|
|
|
Microphone
Amplifiers
|
|
|
RB-MA1
The RB-MA1 consists of a low noise microphone pre-amplifier
for converting mic level signals to line level, or for driving
long lines from microphones to mixing equipment.
|
|
|
RB-MA2
The RB-MA2 consists of two independent low-noise
microphone pre-amplifiers for converting mic level signals to
line level, or for driving long lines from microphones to mixing
equipment.
|
|
|
RB-DMA2
The RB-DMA2 consists of two independent low-noise
microphone pre-amplifiers for converting microphone level signals
to a digital AES/EBU or S/PDIF output. Individual analogue balanced
line level outputs are also produced for use, for example, to
feed talkback systems. The unit can either be used as two independent
microphone amplifiers, or one mic input can be copied to both
channels of the digital output.
|
|
|
|
|
|
Stereo
To Mono Converters
|
|
|
RB-SM1
The RB-SM1 consists of a single stereo converters
which will produce a fully buffered and balanced mono line output
from a stereo input.
|
|
|
RB-SM2
The RB-SM2 consists of two independent converters
which will produce two fully buffered and balanced mono line outputs
from two stereo inputs.
|
|
|
|
|
|
General
Interfaces
|
|
|
RB-LC3
The RB-LC3 is a triple output switching unit for
controlling external mains indicators, primarily studio status
lights for broadcasting applications, such as On-Air, Mic-Live
and Rehearsal/Live lights. Each output can be individually controlled
by one of three remote inputs (pulled high, or low), by a telephony
input (when ringing, or off-hook, or both), or a combination of
two inputs (to control two outputs, e.g. for Rehearsal/Live situations).
The type of control is set using the 12 way DIP switch (4 switches
for each output, allowing 16 different settings).
|
|
|
RB-SD1
The RB-SD1 Silence Detection Unit is used to monitor
an unattended stereo studio feed and in the event of the signal
going 'quiet' after a given period the unit will switch through
an alternative stereo audio signal. This signal could be a recorded
message (e.g. normal service will be resumed. etc), a feed from
a CD player or MiniDisk machine, or an alternative recorded program.
Controls are provided to start external equipment and to provide
remote status indication. The RB-SD1 has a passive signal path
so that it will still allow a signal to be transmitted in the
event of a power failure.
|
|
|
RB-SL2
The RB-SL2 is a stereo, or twin independent mono,
VCA limiter for use in news-rooms and other locations where the
correct level into recording equipment is required, but not necessarily
under the control of an engineer, for example, for overload protection.
It can also be used as an inexpensive main output limiter for
small scale radio stations, hospital radio and student radio.
|
|
|
|
|
|
Digital
Audio Converters
|
|
|
RB-ADDA
The RB-ADDA A/D and D/A converter is a 1U rack-mount
which produces an AES/EBU or S/PDIF level digital audio output
from a balanced XLR or unbalanced phono stereo audio input. It
also produces a stereo balanced XLR or unbalanced phono output
from an incoming AES/EBU or S/PDIF digital input signal.
|
|
|
RB-SC1
Ideal for the transfer of digital audio between
different digital equipment, the RB-SC1 sample rate converter
standardises the sample rate of a digital audio signal to one
of 32kHz, 44.1kHz, 48kHz, 64kHz, 88.2kHz or 96kHz, or to a synchronising
input.
|
|
|
RB-DAC1
Using 24 bit, 96kHz capable devices, the RB-DAC1
D/A Converter is a 1U rack-mount which produces a stereo balanced
XLR or unbalanced phono output from an incoming AES/EBU or S/PDIF
digital input signal. There is also a headphone output with volume
control for monitoring purposes.
|
|
|
RB-SP1
The RB-SP1 Digital Splitter & Combiner is a
1U rack-mount unit used to interface various double sampling pieces
of equipment. Some older equipment uses 2 AES/EBU connectors for
double sampling with each connector carrying an audio signal at
a normal frame rate, whilst other equipment has a single connector
using twice the frame rate. The RB-SP1 can interface between them,
either combining the signals from 2 XLR's into 1, or splitting
the signal from 1 XLR into 2.
|
|
|
|
|
Sonifex
Redbox Rack Mount Kits |
|
RK1
The
RB-RK1 rack mount kit can be attached to the front of the smaller
Redbox products so that they can be rack mounted into a standard
19 inch rack unit.
|
|
RK2
The RB-RK2 rack mount kit can be attached to the
rear of the smaller Redbox products so that they can be rack mounted
into a standard 19 inch rack unit.
|
|
RK3
The RB-RK3 rack mount kit can be attached to the
rear of the larger Redbox products so that they can be rack mounted
into a standard 19 inch rack unit.
|
|
|
|
Sonifex
Redbox Range - Features |
-
All are equipped with IEC mains lead and instruction manual.
-
All are screw mountable as standard and are either rack-mounted
or have the option to be rack-mounted.
-
In-house design and manufacture ensures high quality control
standards.
-
They are manufactured as either 115V 60Hz or 230V 50Hz
and all have a front panel LED power indicator.
-
Manufactured within ISO9000 standards and guaranteed CE
compliant.
-
Housed in eye catching red anodised aluminium cases.
All the Redboxes are screw mountable as standard and are either
rack-mounted or have the option to be rack-mounted. The RB-RK
rack mount kits can be attached to the front or the rear of
the Redbox products so that they can be rack mounted into
a standard 19 inch rack frame in 1U of space.
CLICK
BELOW FOR MORE INFORMATION
|
|
|
Back
|